Gettin' closer on the split house addition

steveinak · Apr 27, 2013

Finally got the split house panel on the boat, now to get it bolted in and move on to the pilot install & reinstall the helm. Still cold here and yup still have snow on the ground, winter just doesn't want to leave this year.

El Mar · Apr 28, 2013

Looking good Steve!!

When do you plan on getting in the water?

Still cold here too.

steveinak · Apr 28, 2013

Its 20 degrees out again this morning

I'm hoping to be in by mid/late May.

MDI45 · Apr 28, 2013

Looks good Steve.....iam thinking of doing the same on my boat someday

steveinak · Apr 28, 2013

Ronnie inspired me to try making some fiberglass angle to use to mount the split house walls with. Used up a lot of scrap pieces of mat i had laying around along with some cloth that i never used for anything.

steveinak · May 6, 2013

Turned into a nice day today so i was able to peel back the tarps on the boat to finally give myself a look what the house addition will look like from a distance. I like what i've done and think its going to make the rig a lot more comfortable.

steveinak · May 7, 2013

Put in a few more hours after dinner and got the door jamb made up. It doesn't get dark here till almost 11pm so lots of work time available.

Raider Ronnie · May 7, 2013

Didn't see this last week

:mrgreen: Glad I could be a source of inspiration !
Not sure what you did for lay up but I did 2 matts, 2 1708 & 2 matts giving me close to 1/4 thickness.
I found the key is not too much glass at a time and go light ( no more than 1%) of the MEK or the the edges will curl in when the resin kicks and not keep it at 90 degrees.
You can also lay some wax paper over and clamp a length of another metal with a round outside corner to hold the 90 degres. I used 2 inch square tubing.
It was a bit of work and not sure any cost savings as I went through some resin but I was advised some pre made fiberglass members (like Strongwell) have a wax throughout and no matter how much grinding you do to prep resin (poly or epoxy) doesn't grab on..
Looks good Steve !

steveinak said:
Ronnie inspired me to try making some fiberglass angle to use to mount the split house walls with. Used up a lot of scrap pieces of mat i had laying around along with some cloth that i never used for anything.
View attachment 12369

View attachment 12370

steveinak · May 9, 2013

pecked away at the jobsite today, bolted in the aluminum angle that holds the partition, got the door jam bolted on and made a pattern for the piece that will butt up against the windshield. Tomorrow its a trip to the plastics joint to go threw the scrap pile to find a nice piece of white UHMW sheet goods and a piece of clear plexi for the window.
cardboard and hot glue gun made short work of making a pattern

rough cut out of window.

finally pulled the blue protective sheet off the windows, wow nice bright cabin interior even with blue tarps covering the boat.

steveinak · May 14, 2013

gettin closer installed outside door handle and lock hasp, had to make a UHMW "keeper" to go over the hasp so it wouldn't flop over and lock me inside the house

made a handle for the inside out of a piece of starboard that i heated with a heat gun while bending it to shape on my metal break.

Old Mud · May 15, 2013

Nice job on forming the starboard Steve, I never thought about bending that stuff. Boy can I think of some projects now.

Hey I made a metal brake almost like that, No trap wire for a tray though.

.

vman · May 15, 2013

Nice job Steve!

steveinak · May 15, 2013

Old Mud said:
Nice job on forming the starboard Steve, I never thought about bending that stuff. Boy can I think of some projects now. Hey I made a metal brake almost like that, No trap wire for a tray though. .

No place around here to buy handles and i bought the stainless outside handle from a outfit online. I've got lots of oddball pieces of plastic so i figured i'd try it and see what it looked like. I made that break when i first started building shrimp pots, same thing i had the scrap angle laying around so i cobbled it together and used it for a few years till i sprung for one of those fancy benders for the trap wire that the guy in rhode island makes. Thats not a tray its just pieces of wire from roll ends, i just can't bring myself to throw out any wire(or anything else

) you never know ????

steelguy · May 15, 2013

Great job Steve. I've thoroughly enjoyed watching the renovation!

F/V First Team · May 16, 2013

steveinak said:
i just can't bring myself to throw out any wire(or anything else) you never know ????

Sounding like a boat builder Steve, always a use for something.

steveinak · May 16, 2013

steelguy said:
Great job Steve. I've thoroughly enjoyed watching the renovation!

Thanks Rob !! now i need you to do your magic and build some funiture for the inside. When are you heading up here ?

steveinak · May 16, 2013

F/V First Team said:
Sounding like a boat builder Steve, always a use for something.

My problem is i can't remember where i put the stuff when i need it! I've been out of gillnetting for 3 years and just got around to selling off the patch web had, i was sorry to see it go, you never know i might be dumb enough and buy another permit for 200 grand and go fish choking again

with the Snow Squall.

steveinak · May 18, 2013

cut the hole for the controls today, only had a couple of hours to work on the boat but finally getting inside, tomorrow i'll tackle moving some wiring to cut the hole for the helm, it going where the wheel is hanging. Ordered the solenoid from Rose's yesterday so the oily mess time is getting close. Couple of interior house shots, it takes more time just thinking how to lay out everything and where to put it with out tearing the whole boat apart than just doing the job. Oh did i mention how happy i am that it SNOWED today !!!